Publications

The paper present the work on PIV-measurements of reactant flow velocity in front of propagating flames in hydrogen-air explosions. The experiments was performed with hydrogen-air mixture at atmospheric pressure and room temperature. The experimental rig was a square channel with 45 × 20 mm2 cross section 300 mm long with a single cylindrical obstacle of blockage ratio 1/3. The equipment used for the PIV-measurements was a Firefly diode laser from Oxford lasers Photron SA-Z high-speed camera and a particle seeder producing 1 μm droplets of water. The gas concentrations used in the experiments was 14 and 17 vol% hydrogen in air. The resulting explosion can be characterized as slow since the maximum flow velocity of the reactants was 13 m/s in the 14% mixture and 23 m/s in the 17% mixture. The maximum flow velocities was measured during the flame-vortex interaction and at two obstacle diameters behind the obstacle. The flame-vortex interaction contributed to the flame acceleration by increasing the overall reaction rate and the flow velocity. The flame area as a function of position is the same for both concentrations as the flame passes the obstacle.

We examine a different approach to complete the decarbonization of the Russian economy in a world where climate policy increasingly requires the radical reduction of emissions wherever possible. We propose an energy system that can supply solar and wind-generated electricity to fulfill demand and which accounts for intermittency problems. This is instead of the common approach of planning for expensive carbon capture and storage and a massive increase in energy efficiency and therefore a drastic reduction in energy use per unit of Gross Domestic Product (GDP). Coupled with this massive increase in alternative energy we also propose using excess electricity to generate green hydrogen. Hydrogen technology can function as storage for future electricity needs or for potential fuel use. Importantly green hydrogen can potentially be used as a replacement export for Russia’s current fossil fuel exports. The analysis was carried out using the highly detailed modeling framework the High-Resolution Renewable Energy System for Russia (HIRES-RUS) representative energy system. The modeling showed that there are a number of feasible combinations of wind and solar power generation coupled with green hydrogen production to achieve 100% decarbonization of the Russian economy.

A core theme of the UK Government's new Industrial Strategy is exploiting opportunities for domestic supply chain development. This extends to a special ‘Automotive Sector Deal’ that focuses on the shift to low emissions vehicles (LEVs). Here attention is on electric vehicle and battery production and innovation. In this paper we argue that a more straightforward gain in terms of framing policy around potential economic benefits may be made through supply chain activity to support refuelling of battery/hydrogen vehicles. We set this in the context of LEV refuelling supply chains potentially replicating the strength of domestic upstream linkages observed in the UK electricity and/or gas industries. We use input-output multiplier analysis to deconstruct and assess the structure of these supply chains relative to that of more import-intensive petrol and diesel supply. A crucial multiplier result is that for every £1million of spending on electricity (or gas) 8 full-time equivalent jobs are supported throughout the UK. This compares to less than 3 in the case of petrol/diesel supply. Moreover the importance of service industries becomes apparent with 67% of indirect and induced supply chain employment to support electricity generation being located in services industries. The comparable figure for GDP is 42%.

Hydrogen has been used as an industrial chemical for more than 100 years. Today hydrogen is used to manufacture ammonia and hence fertilizers as well as methanol and hydrogen peroxide both vital feedstocks for a wide variety of different chemical products. Furthermore in oil refineries hydrogen is used for the processing of intermediate products as well as to increase the hydrogen contents of the final products that are used propel the vehicles. However hydrogen has recently achieved new attention for its capabilities in reducing carbon emissions to the atmosphere. Producing hydrogen via low or totally carbon-free ways and using this “good” low-carbon hydrogen to replace hydrogen with a larger carbon footprint we can reduce carbon emissions. Furthermore using renewable electricity and captured carbon we can synthesise many such chemical products that are currently produced from fossil raw materials. This “Power-to-X” (P2X) is often seen as the eventual incarnation of the hydrogen economy. In addition the progress in technology both in hydrogen fuel cells and in polymer electrolyte electrolysers alike has increased their efficiencies.<br/>Furthermore production costs of renewable electricity by wind or solar power have lowered significantly. Thus cost of “good” hydrogen has also decreased markedly and production volumes are expected to increase rapidly. For these reasons many countries have raised interests in “good” hydrogen and have created roadmaps and strategies for their involvement in hydrogen. Hydrogen plays a key role also in combating climate change and reaching Finland's national goal of carbon neutrality by 2035. In recent years many clean hydrogen and P2X production methods have developed significantly and become commercially viable.<br/>This report was produced by a team of VTT experts on hydrogen and hydrogen-related technologies. The focus is in an outlook for low-carbon H2 production H2 utilization for green chemicals and fuels as well as storage transport and end-use especially during the next 10 years in Finland in connection to renewed EU regulations. This roadmap is expected to serve as the knowledge-base for further work such as shaping the hydrogen policy for Finland and determining the role of hydrogen in the national energy and climate policy.

Damages due to mechanical impacts on the structural integrity of pressure vessels in composite material to store compressed hydrogen can lead to disastrous failures if they are not detected and fixed on time. A wide variety of damage modes in composites such as delamination and fiber breakage introduced by impact is difficult to be detected by conventional methods. Structural Health Monitoring (SHM) provides a system with the ability to detect and interpret adverse changes in a structure like a pressure vessel. Different types of methods will be proposed for damage detection based on comparing signals to baseline recorded from the undamaged structure. Guided wave based diagnosis method is one of the most effective used techniques due to its sensitivity to small defects. The paper pretend to identify the more adequate inspection methods to classify by smart rules based in artificial intelligence the effect of an impact on the structural integrity of the pressure vessel thus improving the level of safety.

This paper is devoted to a benchmarking exercise of the EUROPLEXUS code against several large scale deflagration and detonation experimental data sets in order to improve its hydrogen combustion modeling capabilities in industrial settings. The code employs an algorithm for the propagation of reactive interfaces RDEM which includes a combustion wave as an integrable part of the Reactive Riemann problem propagating with a fundamental flame speed (being a function of initial mixture properties as well as gas dynamics parameters). An improvement of the combustion model is searched in a direction of transient interaction of flames with regions of elevated vorticity/shear in obstacle-laden channels and vented enclosures.

Fundamental understanding of H localization in steel is an important step towards theoretical descriptions of hydrogen embrittlement mechanisms at the atomic level. In this paper we investigate the interaction between atomic H and defects in ferromagnetic body-centered cubic (bcc) iron using density functional theory (DFT) calculations. Hydrogen trapping profiles in the bulk lattice at vacancies dislocations and grain boundaries (GBs) are calculated and used to evaluate the concentrations of H at these defects as a function of temperature. The results on H-trapping at GBs enable further investigating H-enhanced decohesion at GBs in Fe. A hierarchy map of trapping energies associated with the most common crystal lattice defects is presented and the most attractive H-trapping sites are identified.

A prospective global market share of Electric vehicle (EV) Hybrid electric vehicle (HEV) and Hydrogen Fuel Cell Vehicle (HFCV) is expected to grow due to stringent emission regulation and oil depletion. However it is essential to secure protection against high-pressure hydrogen gas and high-voltage in fuel cell vehicles and thus needs to develop a technique for safety assessment of HFCV. In this experiment 8 research institutes including the Korea Automobile Testing and Research Institute Hyundai Motor Company took part in. This project was supported by the Ministry of Land Transportation and Maritime Affairs of the Republic of Korea.

The design of ventilation system has implications for the safety of life and property and the development of regulations and standards in the space with the hydrogen storage equipment. The impact of both the position and the area of a single vent on the dispersion of hydrogen in a cuboid space (with dimensions L x W x H ¼ 2.90 0.74 1.22 m) is investigated with Computational Fluid Dynamics (CFD) in this study. Nine positions of the vent were compared for the leakage taking place at the floor to understand the gas dispersion. It was shown a cloud of 1% mole fraction has been formed near the ceiling of the space in less than 40 s for different positions of the vent which can activate hydrogen sensors. The models show that the hydrogen is removed more effectively when the vent is closer to the leakage position in the horizontal direction. The study demonstrates that the vent height of 1.00 m is safer for the particular scenario considered. The area of the vent has little effect on the hydrogen concentration for all vent positions when the area of the vent is less than 0.045 m2 and the height of the vent is less than 0.61 m.

Passive auto-catalytic recombiners (PARs) are used as safety devices in the containments of nuclear power plants (NPPs) for the removal of hydrogen that may be generated during specific reactor accident scenarios. In the presented study it was investigated whether a PAR designed for hydrogen removal inside a NPP containment would perform principally inside a typical surrounding of hydrogen or fuel cell applications. For this purpose a hydrogen release scenario inside a garage – based on experiments performed by CEA in the GARAGE facility (France) – has been simulated with and without PAR installation. For modelling the operational behaviour of the PAR the in-house code REKO-DIREKT was implemented in the CFD code ANSYS-CFX. The study was performed in three steps: First a helium release scenario was simulated and validated against experimental data. Second helium was replaced by hydrogen in the simulation. This step served as a reference case for the unmitigated scenario. Finally the numerical garage setup was enhanced with a commercial PAR model. The study shows that the PAR works efficiently by removing hydrogen and promoting mixing inside the garage. The hot exhaust plume promotes the formation of a thermal stratification that pushes the initial hydrogen rich gas downwards and in direction of the PAR inlet. The paper describes the code implementation and simulation results.