Publications

The explosion venting is an effective way to reduce hydrogen-air explosion hazards but the explosion venting has been hardly touched in an obstructed container. Current experiments focused on the effects of different blockage ratios on the explosion venting in a small obstructed rectangular container. Experimental results show that three overpressure peaks are formed in the case with the obstacle while only two can be observed in the case of no obstacle. The obstacle blockage ratio has a significant influence on the peak overpressure induced by the obstacle-acoustic interactions but it has an ignorable effect on the peak overpressure caused by the rupture of the vent film. The obstacle-induced overpressure peak first increases and then decreases with the increase of the blockage ratio. In addition all overpressure peaks inside the container decreases with the increase of the vent area and its appearance time is relatively earlier for larger vent area.

In this report a 5 kW PEFC system running on dry hydrogen with an appropriately sized Balance of Plant (BoP) was used to conduct experimental studies and analyses of gas supply subsystems. The improper rating and use of BoP components has been found to increase parasitic loads which consequently has a direct effect on the polymer electrolyte fuel cell (PEFC) system efficiency. Therefore the minimisation of parasitic loads while maintaining desired performance is crucial. Nevertheless little has been found in the literature regarding experimental work on large stacks and BoP with the majority of papers concentrating on modelling. A particular interest of our study was the anode side of the fuel cell. Additionally the rationale behind the use of hydrogen anode recirculation was scrutinised and a novel anode purging strategy was developed and implemented. Through experimental modelling the use of cathode air blower was minimised since it was found to be the biggest contributor to the parasitic loads.

In December 2019 the European Commission unveiled an ambitious project the European Green Deal which aims to lead the European Union to climate neutrality by 2050. This is a significant challenge for all EU countries and especially for Poland. The role of hydrogen in the processes of decarbonization of the economy and transport is being discussed in many countries around the world to find rational solutions to this difficult and complex problem. There is an ongoing discussion about the hydrogen economy which covers the production of hydrogen its storage transport and conversion to the desired forms of energy primarily electricity mechanical energy and new fuels. The development of the hydrogen economy can significantly support the achievement of climate neutrality. The belief that hydrogen plays an important role in the transformation of the energy sector is widespread. There are many technical and economic challenges as well as legal and logistical barriers to deal with in the transition process. The development of hydrogen technologies and a global sustainable energy system that uses hydrogen offers a real opportunity to solve the challenges facing the global energy industry: meeting the need for clean fuels increasing the efficiency of fuel and energy production and significantly reducing greenhouse gas emissions. The paper provides an in-depth analysis of the Polish Hydrogen Strategy a document that sets out the directions for the development of hydrogen use (competences and technologies) in the energy transport and industrial sectors. This analysis is presented against the background of the European Commission’s document ‘A Hydrogen Strategy for a Climate-Neutral Europe’. The draft project presented is a good basis for further discussion on the directions of development of the Polish economy. The Polish Hydrogen Strategy although it was created later than the EU document does not fully follow its guidelines. The directions for further work on the hydrogen strategy are indicated so that its final version can become a driving force for the development of the country’s economy.

This paper proposes a current decoupling controller for a Doubly-fed Induction Generator (DFIG) based on floating offshore wind turbine and power to gas. The proposed controller realizes Maximum Power Point Tracking (MPPT) through integral sliding mode compensation. By using the internal model control strategy an open-loop controller is designed to ensure that the system has good dynamic performance. Furthermore using the integral Sliding Mode Control (SMC) strategy a compensator is designed to eliminate the parameter perturbation and external disturbance of the open-loop control. The parameters of the designed controller are designed through Grey Wolf Optimization (GWO). Simulation results show that the proposed control strategy has better response speed and smaller steady-state error than the traditional control strategy. This research is expected to be applied to the field of hydrogen production by floating offshore wind power.

Storing renewable energy in chemicals like hydrogen can bring various benefits like high energy density seasonal storability possible cost reduction of the final product and the potential to let renewable power penetrate other markets and to overcome their intermittent availability. In the last year’s production of this gas from renewable energy sources via electrolysis has grown its reputation as one feasible solution to satisfy future zero-emission energy demand. To extend the exploitation of Renewable Energy Source (RES) small-scale conversion plants seem to be an interesting option. In view of a possible widespread adoption of these types of plants the authors intend to present the experimental characterization of a small-scale hydrogen production and storage plant. The considered experimental plant is based on an alkaline electrolyser and an air-driven hydrogen compression and storage system. The results show that the hydrogen production-specific consumption is on average 77 kWh/kgH2 . The hydrogen compressor energy requirement is on average 15 kWh/kgH2 (data referred to the driving compressed air). The value is higher than data found in literature (4.4–9.3 kWh/kgH2 ) but the difference can be attributed to the small size of the considered compressor and the choice to limit the compression stages.

There is a large literature exploring possible hydrogen futures using various modelling and scenario approaches. This paper compares the rates of transition depicted in that literature with a set of historical analogies. These analogies are cases in which alternative-fuelled vehicles have penetrated vehicle markets. The paper suggests that the literature has tended to be optimistic about the possible rate at which hydrogen vehicles might replace oil-based transportation. The paper compares 11 historical adoptions of alternative fuel vehicles with 24 scenarios from 20 studies that depict possible hydrogen futures. All but one of the hydrogen scenarios show vehicle adoption faster than has occurred for hybrid electric vehicles in Japan the most successful market for hybrids. Several scenarios depict hydrogen transitions occurring at a rate faster than has occurred in any of the historic examples. The paper concludes that scenarios of alternative vehicle adoption should include more pessimistic scenarios alongside optimistic ones.

Gaseous fuels with low life-cycle emissions of greenhouse gases (GHG) play a prominent role in the European Union’s (EU) decarbonization plans. Renewable and low-GHG hydrogen are highlighted in the ambitious goals for a cross-sector hydrogen economy laid out in the European Commission’s Hydrogen Strategy. Renewable hydrogen and biomethane are given strong production incentives in the Commission’s proposed revision to the Renewable Energy Directive (REDII). The EU uses life-cycle analysis (LCA) to determine whether renewable gas pathways meet the GHG reduction thresholds for eligibility in the REDII. This study aims to support European policymakers with a better understanding of the uncertainties regarding gaseous fuels’ roles in meeting climate goals. Life-cycle GHG analysis is complex and differences in methodology as well as data inputs and assumptions can spell the difference between a renewable gas pathway qualifying or not for REDII eligibility at the 50% to 80% GHG reduction level. It is thus important for European policymakers to use robust LCA to ensure that policy only supports gas pathways consistent with a vision of deep decarbonization. For this purpose we conduct sensitivity analysis of the life-cycle GHG emissions of a number of low-GHG gas pathways including biomethane produced from four feedstocks: wastewater sludge manure landfill gas (LFG) and silage maize; and hydrogen produced from eight sources: natural gas combined with carbon capture and storage (CCS) coal with CCS biomass gasification renewable electricity 2030 EU grid electricity wastewater sludge biomethane manure biomethane and LFG biomethane. For each pathway we estimate the life-cycle GHG intensity using a default central case identify key parameters that strongly affect the fuel’s GHG intensity and conduct a sensitivity analysis by changing these key parameters according to the range of possible values collected from the literature. Figure ES1 summarizes the full range of possible GHG intensities for each gaseous pathway we analyzed in this study—biomethane is depicted in the top figure and hydrogen is shown in the bottom. The bars represent the GHG intensity of the central case and vertical error bars indicate the maximum and minimum GHG intensity of each pathway according to our sensitivity analysis. The dotted orange horizontal line illustrates the fossil comparator which is 94 grams of carbon dioxide equivalent per megajoule (gCO2e/MJ) for transport fuels in the REDII. The dotted yellow line represents the GHG intensity of a 65% GHG reduction goal for biomethane used in the transportation sector or 70% GHG reduction for hydrogen. Pathways are situated from left to right in increasing order of GHG intensity of the central case. Comparing the central cases of the four biomethane pathways the waste-based biomethane pathways generally have negative GHG intensity. However considering the uncertainty in these GHG intensities manure biomethane might have more limited carbon reduction potential in the 100-year timeframe if methane leakage from its production process is high. In contrast wastewater sludge biomethane and LFG biomethane even after accounting for uncertainties retain relatively low GHG emissions. On the other hand biomethane produced from silage maize can have much higher emissions; in the central case we find that silage maize biogas only reduces GHG emissions by 30% relative to the fossil comparator—the low carbon reduction potential is due to the significant emissions emerging from direct and indirect land use change involved in growing maize. Taking into account the variation in assumptions silage maize biomethane can be worse for the climate than fossil fuels.

Sustainability transportation is characterized by a positive externality on the environment health social security land use and social inclusion. The increasing interest in global warming has caused attention to be paid to the introduction of the hydrogen bus (H2B). When introducing new environmental technologies such as H2B it is often necessary to assess the environmental benefits related to this new technology. However such benefits are typically non-priced due to their public good nature. Therefore we have to address this problem using the contingent valuation (CV) method. This method has been developed within environmental economics as a means to economically assess environmental changes which are typically not traded in the market. So far several big cities have been analyzed to evaluate the perceived benefit related to H2B introduction but to the best of our knowledge no one has performed a CV analysis of a historical city where smog also damages historical buildings. This paper presents the results obtained using a multi-wave survey. We have investigated user preferences to elicit their willingness to pay for H2B introduction in Perugia taking into account all types of negative externalities due to the traffic pollution. The results confirm that residents in Perugia are willing to pay extra to support the introduction of H2B.

Alkaline water electrolysis powered by renewable energy sources is one of the most promising strategies for environmentally friendly hydrogen production. However wind and solar energy sources are highly dependent on weather conditions. As a result power fluctuations affect the electrolyzer and cause several negative effects. Considering these limiting effects which reduce the water electrolysis efficiency a novel operation strategy is proposed in this study. It is based on pumping the electrolyte according to the current density supplied by a solar PV module in order to achieve the suitable fluid dynamics conditions in an electrolysis cell. To this aim a mathematical model including the influence of electrode-membrane distance temperature and electrolyte flow rate has been developed and used as optimization tool. The obtained results confirm the convenience of the selected strategy especially when the electrolyzer is powered by renewable energies.

Hydrogen storage in the solid state represents one of the most attractive and challenging ways to supply hydrogen to a proton exchange membrane (PEM) fuel cell. Although in the last 15 years a large variety of material systems have been identified as possible candidates for storing hydrogen further efforts have to be made in the development of systems which meet the strict targets of the Fuel Cells and Hydrogen Joint Undertaking (FCH JU) and U.S. Department of Energy (DOE). Recent projections indicate that a system possessing: (i) an ideal enthalpy in the range of 20–50 kJ/mol H2 to use the heat produced by PEM fuel cell for providing the energy necessary for desorption; (ii) a gravimetric hydrogen density of 5 wt. % H2 and (iii) fast sorption kinetics below 110 ◦C is strongly recommended. Among the known hydrogen storage materials amide and imide-based mixtures represent the most promising class of compounds for on-board applications; however some barriers still have to be overcome before considering this class of material mature for real applications. In this review the most relevant progresses made in the recent years as well as the kinetic and thermodynamic properties experimentally measured for the most promising systems are reported and properly discussed.