Chinese Taipei

Consumption of fossil fuels especially in transport and energy-dependent sectors has led to large greenhouse gas production. Hydrogen is an exciting energy source that can serve our energy purposes and decrease toxic waste production. Decomposition of methane yields hydrogen devoid of COx components thereby aiding as an eco-friendly approach towards large-scale hydrogen production. This review article is focused on hydrogen production through thermocatalytic methane decomposition (TMD) for hydrogen production. The thermodynamics of this approach has been highlighted. Various methods of hydrogen production from fossil fuels and renewable resources were discussed. Methods including steam methane reforming partial oxidation of methane auto thermal reforming direct biomass gasification thermal water splitting methane pyrolysis aqueous reforming and coal gasification have been reported in this article. A detailed overview of the different types of catalysts available the reasons behind their deactivation and their possible regeneration methods were discussed. Finally we presented the challenges and future perspectives for hydrogen production via TMD. This review concluded that among all catalysts nickel ruthenium and platinum-based catalysts show the highest activity and catalytic efficiency and gave carbon-free hydrogen products during the TMD process. However their rapid deactivation at high temperatures still needs the attention of the scientific community.

The rotary engine (RE) is a potential power plant for unmanned aerial vehicles (UAVs) and automobiles because of its structural and design merits. However it has some serious drawbacks such as frequent maintenance requirements and excessive fuel consumption. This review paper presents the current status of hydrogen-fueled rotary engine (HRE) technology and identifies the existing research and development gaps in combustion efficiency and performance of this engine that might benefit transportation sector. Focusing primarily on the research from past ten years the crucial challenges encountered in hydrogen-powered rotary engines have been reviewed in terms of knock hydrocarbon (HC) emissions and seal leakages. The paper identifies the recent advances in design concepts and production approaches used in hydrogen-fueled rotary engines such as geometric models of trochoid profiles port configurations fuel utilization systems and currently available computational fluid dynamics (CFD) tools. This review article is an attempt to collect and organize literature on existing design methods up to date and provide recommendations for further improvements in RE technology.

Human activities have exacerbated global greenhouse effects resulting in extreme climate changes that have caused disasters and food and water shortages in recent years. Transport activities are the one of the main causes of global greenhouse gas (GHG) emissions. Therefore policy makers must develop some strategies to reduce GHG emissions. One of the Taiwan’s transportation policies intended to reduce CO2 emissions is to replace all traditional diesel fuel urban buses with alternative energy buses. This paper uses a case study of bus route NO. 2 in Tainan City and follows the international standard ISO/TS 14067 and PAS2050 to measure the carbon footprints of different energy buses. The purpose is to measure the environmental benefits of alternative energy buses. The results of the bus carbon footprints from high to low were LNG buses 63.14g CO2e/pkm; traditional diesel buses 54.6g CO2e/pkm; liquefied petroleum gas buses 47.4g CO2e/pkm; plug-in electric buses 37.82g CO2e/pkm and hydrogen fuel cell bus es 29.17g CO2e/pkm respectively. It was also found that the use of hydrogen fuel cell buses would potentially reduce CO2e emissions in Tainan City by 1244081 tons which at this time is only city bus No. 2. If all the Taiwan city buses were switched to hydrogen fuel cell buses this would potentially reduce CO2e by 227832.39 tons. The effect of the reduction in carbon emissions from the use of hydrogen fuel cells buses in all Taiwanese urban areas is the equivalent of planting 22.78 million trees. It is thus suggested that the government use hydrogen fuel cell buses as the future of the country’s major alternative energy buses since they are the most environmentally friendly alternative to reducing CO2 emissions.

Hydrogen embrittlement in metals (HE) is a serious challenge for the use of high strength materials in engineering practice and a major barrier to the use of hydrogen for global decarbonization. Here we describe the factors and variables that determine HE susceptibility and provide an overview of the latest understanding of HE mechanisms. We discuss hydrogen uptake and how it can be managed. We summarize hydrogen trapping and the techniques used for its characterization. We also review literature that argues that hydrogen trapping can be used to decrease HE susceptibility. We discuss the future research that is required to advance the understanding of HE and hydrogen trapping and to develop HE-resistant alloys.