United States

Hydrogen is often viewed as an important energy carrier in a future decarbonized world. Currently most hydrogen is produced by steam reforming of methane in natural gas (“gray hydrogen”) with high carbon dioxide emissions. Increasingly many propose using carbon capture and storage to reduce these emissions producing so-called “blue hydrogen” frequently promoted as low emissions. We undertake the first effort in a peer-reviewed paper to examine the lifecycle greenhouse gas emissions of blue hydrogen accounting for emissions of both carbon dioxide and unburned fugitive methane. Far from being low carbon greenhouse gas emissions from the production of blue hydrogen are quite high particularly due to the release of fugitive methane. For our default assumptions (3.5% emission rate of methane from natural gas and a 20-year global warming potential) total carbon dioxide equivalent emissions for blue hydrogen are only 9%-12% less than for gray hydrogen. While carbon dioxide emissions are lower fugitive methane emissions for blue hydrogen are higher than for gray hydrogen because of an increased use of natural gas to power the carbon capture. Perhaps surprisingly the greenhouse gas footprint of blue hydrogen is more than 20% greater than burning natural gas or coal for heat and some 60% greater than burning diesel oil for heat again with our default assumptions. In a sensitivity analysis in which the methane emission rate from natural gas is reduced to a low value of 1.54% greenhouse gas emissions from blue hydrogen are still greater than from simply burning natural gas and are only 18%-25% less than for gray hydrogen. Our analysis assumes that captured carbon dioxide can be stored indefinitely an optimistic and unproven assumption. Even if true though the use of blue hydrogen appears difficult to justify on climate ground

The Pd-H system has attracted extensive attention. Pd can absorb considerable amount of H at room temperature this ability is reversible so it is suitable for multiple energy applications. Pd-Ag alloys possess higher H permeability solubility and narrower miscibility gap with better mechanical properties than pure Pd but sulfur poisoning remains an issue. Pd-Cu alloys have excellent resistance to sulfur and carbon monoxide poisoning and hydrogen embrittlement good mechanical properties and broader temperature working environments over pure Pd but relatively lower hydrogen permeability and solubility than pure Pd and Pd-Ag alloys. This suggests that alloying Pd with Ag and Cu to create Pd-Ag-Cu ternary alloys can optimize the overall performance and substantially lowers the cost. Thus in this paper we provide the first embedded atom method potentials for the quaternary hydrides Pd_1-y-zAgyCu_zH_x. The fully analytical potentials are fitted utilizing the central atom method without performing time-consuming molecular dynamics simulations.

The European Community requires a vehicle-level bonfire test for vehicles using plastic fuel tanks for conventional fuels (ECE R-34 Annex 5). A similar test could be applied to hydrogen-fuelled vehicles. It would test a realistic vehicle with its complete fuel and safety systems. An advantage of such a test is that the same test could be applied independent of the hydrogen storage technology (compressed gas liquid or hydride). There are currently standards for bonfire testing of a bare Compressed Natural Gas (CNG) tank and its Pressure Relief Device (PRD). This standard is FMVSS 304 in the U.S. and ISO 15869-1 in Europe. Japan has a similar standard. It requires that a bare tank and its associated PRD be subjected to a propane flame for 20 minutes. The tank must either survive or safely vent its contents. No modern composite wound tank is expected to survive for 20 minutes – so this is not a tank test but really a PRD test. The test procedure requires the PRD to be shielded from direct impingement of the flames – but the shield is not well specified. If it shields the PRD too well the PRD will not activate and the tank will burst. This paper describes the results of a CNG and a hydrogen tank burst from such tests. The mechanical energy released is enormous. It is simply unacceptable to allow the tank to burst – the PRD and venting system must work. Organizations in the U.S Europe and Japan are in the process of modifying the CNG tank bonfire test for compressed hydrogen storage. A bare tank with a single PRD is not a good simulation of a hydrogen fuel system installed in an actual vehicle. There will usually be multiple tanks plumbed together at either the tank pressure or at the intermediate pressure (after the pressure regulator). There may be more than one PRD. The tank may be shielded (from debris) or insulated to protect it from an underbody pool fire. Also the heat transfer from the simulated pool fire (propane flame) will be very different when mounted in a vehicle versus the bare tank test. A vehicle-level pool fire test will alleviate these problems. It is therefore recommended that the bare tank test be replaced by or augmented with a vehicle-level bonfire test similar to ECE R-34 Annex 5.

Replacement of precious catalyst with cost-effective alternatives would be significantly beneficial for hydrogen production via electrocatalytic hydrogen evolution reaction (HER). All candidates thus far are exclusively metallic catalysts which suffer inherent corrosion and oxidation susceptibility during acidic proton-exchange membrane electrolysis. Herein based on theoretical predictions we designed and synthesized nitrogen (N) and phosphorus (P) dual-doped graphene as a non-metallic electrocatalyst for sustainable and efficient hydrogen production. The N and Phetero-atoms could coactivate the adjacent C atom in the graphene matrix by affecting its valence orbital energy levels to induce a synergistically enhanced reactivity toward HER. As a result the dual-doped graphene showed higher electrocatalytic HER activity than single-doped ones and comparable performance to some of the traditional metallic catalysts.

Proton conducting SmNiO₃ (SNO) thin films were grown on (001) LaAlO₃ substrates for systematically investigating the proton transport properties. X-ray Diffraction and Atomic Force Microscopy studies reveal that the as-grown SNO thin films have good single crystallinity and smooth surface morphology. The electrical conductivity measurements in air indicate a peak at 473 K in the temperature dependence of the resistance of the SNO films probably due to oxygen loss on heating. A Metal-Insulator-Transition occurs at 373 K for the films after annealing at 873 K in air. In a hydrogen atmosphere (3% H2/97% N₂) an anomalous peak in the resistance is found at 685 K on the first heating cycle. Electrochemical Impedance Spectroscopy studies as a function of temperature indicate that the SNO films have a high ionic conductivity (0.030 S/cm at 773 K) in a hydrogen atmosphere. The activation energy for proton conductivity was determined to be 0.23 eV at 473–773 K and 0.37 eV at 773–973 K respectively. These findings demonstrate that SNO thin films have good proton conductivity and are good candidate electrolytes for low temperature proton-conducting Solid Oxide Fuel Cells.

A suitably trained emergency response force is an essential component for safe implementation of any type of fuel infrastructure. Because of the relative newness of hydrogen as a fuel however appropriate emergency response procedures are not yet well understood by responder workforces across the United States and around the world. A significant near-term training effort is needed to ensure that the future hydrogen infrastructure can be developed and operated with acceptable incident risk. Efforts are presently underway at the HAMMER site in Washington State to develop curricula related to hydrogen properties and behavior identification of problems (e.g. incorrect equipment installation) and appropriate response and other relevant information intended for classroom instruction. In addition a number of hands-on training props are planned for realistic simulation of hydrogen incidents in order to convey proper response procedures in high-pressure cryogenic high leakage or other high-risk accident situations. Surveys of emergency responders fire marshals regulatory authorities manufacturers and others are being undertaken to ensure that the capabilities developed and offered at HAMMER will meet the acknowledged need. This paper describes the training curricula and props anticipated at HAMMER and is intended to provide useful information to others planning similar training programs.

This study is aimed at the validation of the pressure peaking phenomenon against laboratory-scale experiments. The phenomenon was discovered recently as a result of analytical and numerical studies performed at Ulster University. The phenomenon is characterized by the existence of a peak on the overpressure transient in an enclosure with vent(s) at some conditions. The peak overpressure can significantly exceed the steady-state pressure and jeopardise a civil structure integrity causing serious life safety and property protection problems. However the experimental validation of the phenomenon was absent until recently. The validation experiments were performed at Karlsruhe Institute of Technology within the framework of the HyIndoor project. Tests were carried out with release of three different gases (air helium and hydrogen) within a laboratory-scale enclosure of about 1 m3 volume with a vent of comparatively small size. The model of pressure peaking phenomenon reproduced closely the experimental pressure dynamics within the enclosure for all three used gases. The prediction of pressure peaking phenomenon consists of two steps which are explained in detail. Examples of calculation for typical hydrogen applications are presented.

We have developed a web-based hydrogen safety class and are developing a hands-on hydrogen safety class. The 4-h web-based class is directed to laboratory researchers who need basic hydrogen safety information (free online access at http://www.h2labsafety.org/) and it addresses hydrogen fundamentals: properties pressure and cryogenic safety emergency response and codes and standards. Technical operators in charge of building and testing experimental hydrogen equipment will also soon benefit from a more comprehensive 3-day hands-on safety class that will present detailed information for installation testing and operation of hydrogen pressurized systems. The hands-on class includes a full day of classroom instruction followed by two days of laboratory work where students assemble test and operate a pressure system based on a schematic and component description.

Stationary pressure vessels for the storage of large volumes of gaseous hydrogen at high pressure (>70 MPa) are typically manufactured from Cr-Mo steels. These steels display hydrogen-enhanced fatigue crack growth but pressure vessels can be manufactured using defect-tolerant design methodologies. However storage volumes are limited by the wall thickness that can be reliably manufactured for quench and tempered Cr-Mo steels typically not more than 25-35 mm. High-hardenability steels can be manufactured with thicker walls which enables larger diameter pressure vessels and larger storage volumes. The goal of this study is to assess the fracture and fatigue response of high hardenability Ni-Cr-Mo pressure vessel steels for use in high-pressure hydrogen service at pressure in excess of 1000 bar. Standardized fatigue crack growth tests were performed in gaseous hydrogen at frequency of 1Hz and for R-ratios in the range of 0.1 to 0.7. Elastic-plastic fracture toughness measurements were also performed. The measured fatigue and fracture behavior is placed into the context of previous studies on fatigue and fracture of Cr-Mo steels for gaseous hydrogen.

During the current global financial crisis the term “Risk Management” is often heard. Just as the causes for the financial problems are elusive so is a complete definition of what Risk Management means. The answer is highly dependent upon your perceptions of “risk” and your appetite for assuming risks. The proposed paper will explore these issues with some brief case studies as they apply to hydrogen industrial applications hydrogen refuelling stations and fuel cell technologies for distributed generation.

Specifically the paper will identify the various risk exposures from the perspective of the project developers original equipment suppliers end users project funding sources and traditional insurance providers. What makes this evaluation intriguing is that it is a mixed bag of output capacities Combine Heat & Power (CHP) potential and technology maturity. Therefore the application considerations must be part of any overall Risk Management program.