United Kingdom

The turbine-combined free-piston engine generator (TCFPEG) is a hybrid machine generating both mechanical work from the gas turbine and electricity from the linear electric generator for battery charging. In the present study the system performance of the designed TCFPEG system is predicted using a validated numerical model. A parametric analysis is undertaken based on the influence of the engine load valve timing the number of linear generators adopted and different fuels on the system performance. It is found that when linear electric generators are connected with the free-piston gas turbine the bottom dead centre the peak piston velocity and engine operation frequency are all reduced. Very minimal difference on the in-cylinder pressure and the compressor pressure is observed while the peak pressure in the bounce chamber is reduced. When coupled with a linear electric generator the system efficiency can be improved to nearly 50% by optimising engine load and the number of the linear generators adopted in the TCFPEG system. The system is able to be operated with different fuels as the piston is not limited by a mechanical system; the output power and system efficiency are highest when hydrogen is used as the fuel.

Hydrogen dispersion in stagnant environment resulting from blowdown of a vessel storing the gas at cryogenic temperature is simulated using different CFD codes and modelling strategies. The simulations are based on the DISCHA experiments that were carried out by Karlsruhe Institute of Technology (KIT) and Pro-Science (PS). The selected test for the current study involves hydrogen release from a 2.815 dm3 volume tank with an initial pressure of 200 barg and temperature 80 K. During the release the hydrogen pressure in the tank gradually decreased. A total of about 139 gr hydrogen is released through a 4 mm diameter. The temperature time series and the temperature decay rate of the minimum value predicted by the different codes are compared with each other and with the experimentally measured ones. Recommendations for future experimental setup and for modeling approaches for similar releases are provided based on the present analysis. The work is carried out within the EU-funded project PRESLHY.

Existing studies of financing efficiency concentrate on capital structure and a single external environment or internal management characteristic. Few of the studies include the internal and external financing environments at the same time for hydrogen energy industry financing efficiency. This paper used the data envelopment analysis (DEA) model and the Malmquist index to measure the financing efficiency of 70 hydrogen energy listed enterprises in China from 2014 to 2020 from both static and dynamic perspectives. Then a tobit model was constructed to explore the influence of external environment and internal factors on the financing efficiency. The contributions of this paper are studying the internal and external financing environments and integrating financing cost efficiency and capital allocation efficiency into the financing efficiency of hydrogen energy enterprises. The results show that firstly the financing efficiency of China’s hydrogen energy listed enterprises showed an upward trend during the years 2014–2020. Secondly China’s hydrogen energy enterprises mainly gather in the eastern coastal areas and their financing efficiency is more than that in western areas. Thirdly the regional economic development level enterprise scale financing structure capital utilization efficiency and profitability have significant effects on the financing efficiency. These results can promote the achievement of “carbon neutrality” in China.

Clean renewable energy for Chinese cities is a priority in air quality improvement. This paper describes the recent Chinese advances in Polymer Electrolyte Membrane (PEM) hydrogen-fuel-cell-battery vehicles including buses and trucks. Following the 2016 Chinese government plan for new energy vehicles bus production in Foshan has now overtaken that in the EU USA and Japan combined. Hydrogen infrastructure requires much advance to catch up but numbers of filling stations are now increasing rapidly in the large cities. A particular benefit in China is the large number of battery manufacturing companies which fit well into the energy storage plan for hybrid fuel cell buses. The first city to manufacture thousands of PEM-battery hybrid buses is Foshan where the Feichi (Allenbus) company has built a new factory next to a novel fuel cell production line capable of producing 500 MW of fuel cell units per year. Hundreds of these buses are running on local Foshan routes this year while production of city delivery trucks has also been substantial. Results for energy consumption of these vehicles are presented and fitted to the Coulomb theory previously delineated.

The thermal management system architectures proposed for hydrogen-powered propulsion technologies are critically reviewed and assessed. The objectives of this paper are to determine the system-level shortcomings and to recognise the remaining challenges and research questions that need to be sorted out in order to enable this disruptive technology to be utilised by propulsion system manufacturers. Initially a scientometrics based co-word analysis is conducted to identify the milestones for the literature review as well as to illustrate the connections between relevant ideas by considering the patterns of co-occurrence of words. Then a historical review of the proposed embodiments and concepts dating back to 1995 is followed. Next feasible thermal management system architectures are classified into three distinct classes and its components are discussed. These architectures are further extended and adapted for the application of hydrogen-powered fuel cells in aviation. This climaxes with the assessment of the available evidence to verify the reasons why no hydrogen-powered propulsion thermal management system architecture has yet been approved for commercial production. Finally the remaining research challenges are identified through a systematic examination of the critical areas in thermal management systems for application to hydrogen-powered air vehicles’ engine cooling. The proposed solutions are discussed from weight cost complexity and impact points of view by a system-level assessment of the critical areas in the field.

The thermochemical water‐splitting method is a promising technology for efficiently con verting renewable thermal energy sources into green hydrogen. This technique is primarily based on recirculating an active material capable of experiencing multiple reduction‐oxidation (redox) steps through an integrated cycle to convert water into separate streams of hydrogen and oxygen. The thermochemical cycles are divided into two main categories according to their operating temperatures namely low‐temperature cycles (<1100 °C) and high‐temperature cycles (<1100 °C). The copper chlorine cycle offers relatively higher efficiency and lower costs for hydrogen production among the low‐temperature processes. In contrast the zinc oxide and ferrite cycles show great potential for developing large‐scale high‐temperature cycles. Although several challenges such as energy storage capacity durability cost‐effectiveness etc. should be addressed before scaling up these technologies into commercial plants for hydrogen production. This review critically examines various aspects of the most promising thermochemical water‐splitting cycles with a particular focus on their capabilities to produce green hydrogen with high performance redox pairs stability and the technology maturity and readiness for commercial use.

According to the UK’s Committee on Climate Change the economically efficient achievement of Government’s legally-binding carbon-reduction target will require full decarbonisation of all heat in buildings and the decarbonisation of most industrial heat over the next 20 to 30 years (BEIS 2018). This goliath task is not unprecedented. Indeed the scale of this transition is similar to the UK’s former transition from coal to natural gas heating. Albeit the rate of transition away from natural gas will certainly need to be greater than the rate of the transition toward natural gas to achieve net zero greenhouse gas emissions by 2050.<br/><br/>At present Government’s commitment stands in sharp contrast with its inaction on heat decarbonisation to date. Under pressure to progress this agenda Government has charged the Clean Heat Directorate with the task of outlining the process for determining the UK’s long-term heat policy framework to be published in the ‘Roadmap for policy on heat decarbonisation’ in the summer of 2020 (BEIS 2017). This report resulting from one of six EPSRC-funded secondments is designed to support early thinking on the roadmap by answering the research question: How can ‘Transitions’ research informs the roadmap for governing the UK’s heating transition?<br/><br/>‘Transitions’ research is an interdisciplinary field of study within the Social Sciences and Humanities that investigates the co-evolution of social and technological systems (such as the UK heating system) and the dynamics by which fundamental change in these systems occur. To investigate what insights this area of research may hold for the governance of the UK’s heat transition a systematic literature review was conducted focusing specifically on past and ongoing heat transitions across Europe.<br/><br/>The review uncovered learnings about the role of path dependency; power and politics; complexity; cross-sector interactions; multi-level governance; and intermediaries in shaping non-linear transitions toward renewable heat. This report illustrates each learning with real-world examples from case studies undertaken by Transitions researchers and concludes with a long list of policy and process-oriented governance recommendations for the UK Government.

Hydrogen storage in nanoporous materials has been attracting a great deal of attention in recent years as high gravimetric H2 capacities exceeding 10 wt% in some cases can be achieved at 77 K using materials with particularly high surface areas. However volumetric capacities at low temperatures and both gravimetric and volumetric capacities at ambient temperature need to be improved before such adsorbents become practically viable. This article therefore discusses approaches to increasing the gravimetric and volumetric hydrogen storage capacities of nanoporous materials and maximizing the usable capacity of a material between the upper storage and delivery pressures. In addition recent advances in machine learning and data science provide an opportunity to apply this technology to the search for new materials for hydrogen storage. The large number of possible component combinations and substitutions in various porous materials including Metal-Organic Frameworks (MOFs) is ideally suited to a machine learning approach; so this is also discussed together with some new material types that could prove useful in the future for hydrogen storage applications.

In this work we present the experimental results obtained from hydrogen fuelled spark-ignited dual piston free-piston engine generator (FPEG) prototype operated in two-stroke and four-stroke mode. The FPEG testing was successfully conducted at 3.7 compression ratio engine speed between 5 Hz and 11 Hz and with different equivalence ratios. The FPEG technical details experimental set-up and operational control are explained in detail. Performance indicators show that both equivalence ratio and engine speed affect the engine operation characteristics. For every set of specified FPEG parameters appropriate range of equivalence ratio is recommended to prevent unwanted disturbance to electric generator operation. Both two-stroke and four-stroke cycle mode were tested and the results showed different combustion characteristics with the two thermodynamic cycles. Four-stroke cycle mode could operate with indicated thermal efficiency gain up to 13.2% compared with the two-stroke cycle.

The bioanode is important for a microbial electrolysis cell (MEC) and its robustness to maintain its catalytic activity affects the performance of the whole system. Bioanodes enriched at a potential of +0.2 V (vs. standard hydrogen electrode) were able to sustain their oxidation activity when the anode potential was varied from -0.3 up to +1.0 V. Chronoamperometric test revealed that the bioanode produced peak current density of 0.36 A/m2 and 0.37 A/m2 at applied potential 0 and +0.6 V respectively. Meanwhile hydrogen production at the biocathode was proportional to the applied potential in the range from -0.5 to  -1.0 V. The highest production rate was 7.4 L H2/(m2 cathode area)/day at -1.0 V cathode potential. A limited current output at the bioanode could halt the biocathode capability to generate hydrogen. Therefore maximum applied potential that can be applied to the biocathode was calculated as -0.84 V without overloading the bioanode.