Applications & Pathways

This paper presents a greedy energy management strategy based on model predictive control (MPC) for a stand-alone microgrid powered by photovoltaic (PV) arrays and equipped with batteries and a power-to-hydrogen-to-power (P2H2P) system. The proposed strategy consists of a day-ahead plan and an intra-day dispatch method. In the planning stage the sequence of plan is to determine the power of each storage device for a certain period which is initially generated under the principle that PV arrays have the highest priority followed by the batteries and finally the P2H2P system using short-term forecast data of both load and solar irradiance. The initial plan can be optimized with objectives of harvesting more PV generation in storage and minimizing unmet load through rescheduling P2H2P system and batteries. Three parameters including reserved capacity of batteries predischarge coefficient of fuel cell (FC) and greedy coefficient of electrolyzer (EL) are introduced during plan optimization process to enhance the robustness against forecast errors. In the dispatching stage the energy dispatch is subject to the scheduled plan and the operational constraints. To demonstrate the capabilities of the proposed strategy a case study is performed for a hotel with a mean power consumption of 1567 kWh/day based on the system configuration optimized by HOMER software in comparison with the load following (LF) strategy and the global optimum solution solved by mixed integer linear programing (MILP). The simulation results show that the annual unmet load using the proposed strategy is reduced from 13434 kWh to 2370 kWh which is 528 kWh lower than the optimum solution. Meanwhile the cost of energy (COE) of the proposed strategy decreases by US$ 0.08/kWh compared to the LF strategy and is equal to the optimum solution. Finally the performance of configuration optimization employing genetic algorithm (GA) under different energy management strategies is investigated with the objective function of minimizing the net present cost (NPC). Furthermore the robustness of the proposed strategy is studied. The results show that the proposed strategy gives an NPC and COE of US$ 2.4 million (Mn) and US$ 0.43/kWh which are 23.4% and 9.7% lower than those of systems utilizing the SoC-based strategy and the LF strategy respectively. The results also demonstrate that the strategy is robust against forecast errors especially for overestimated forecast models.

This paper is based on a position paper of the German Industry Association Concentrated Solar Power e.V. to the German government and discusses options on how to decarbonize the heat demand of the domestic industry. Among other option concentration solar collectors are a suitable option in Germany which has not been expected by many experts. The paper derives requirements that are needed to ensure a quick and sustainable way to decarbonize industrial heat demand. They are considered to also be relevant for many other countries that follow the same ambition to become climate neutral in the next decades. They major statements are: A mix of different renewable energy technologies in conjunction with efficiency measures is needed to ensure a secure climate-friendly and cost-efficient heat supply for the industry; The different technology options for the provision of heat from renewable sources through electrification and through hydrogen can and must be combined and integrated with each other. In this context concentrating solar thermal represents an important part of the hybrid supply portfolio of a decarbonized industry This requires: The definition of an expansion target for process heat and the flanking measures; Ensuring the equivalence of renewable heat renewable electricity and green hydrogen - also as hybrid solutions; The promotion of concentrating solar thermal reference projects as an impetus for market ramp-up in Germany; The launch of an information campaign for heat consumers and the establishment of a pool of consultants.

Hydrogen is a carbon-free fuel that can be produced in many ways starting from different sources. Its use as a fuel in internal combustion engines could be a method of significantly reducing their environmental impact. In spark-ignition (SI) engines lean hydrogen–air mixtures can be burnt. When a gaseous fuel like hydrogen is port-injected in an SI engine working with lean mixtures supercharging becomes very useful in order not to excessively penalize the engine performance. In this work the performance of a turbocharged PFI spark-ignition engine fueled by hydrogen has been investigated by means of 1-D numerical simulations. The analysis focused on the engine behavior both at full and partial load considering low and medium engine speeds (1500 and 3000 rpm). Equivalence ratios higher than 0.35 have been considered in order to ensure acceptable cycle-to-cycle variations. The constraints that ensure the safety of engine components have also been respected. The results of the analysis provide a guideline able to set up the load control strategy of a SI hydrogen engine based on the variation of the air to fuel ratio boost pressure and throttle opening. Furthermore performance and efficiency of the hydrogen engine have been compared to those of the base gasoline engine. At 1500 and 3000 rpm except for very low loads the hydrogen engine load can be regulated by properly combining the equivalence ratio and the boost pressure. At 3000 rpm the gasoline engine maximum power is not reached but for each engine load lean burning allows the hydrogen engine achieving much higher efficiencies than those of the gasoline engine. At full load the maximum power output decreases from 120 kW to about 97 kW but the engine efficiency of the hydrogen engine is higher than that of the gasoline one for each full load operating point.

Recent advances in technologies for the decentralized islanded ammonia economy are reviewed with an emphasis on feasibility for long-term practical implementation. The emphasis in this review is on storage systems in the size range of 1–10 MW. Alternatives for hydrogen production nitrogen production ammonia synthesis ammonia separation ammonia storage and ammonia combustion are compared and evaluated. A conceptual process design based on the optimization of temperature and pressure levels of existing and recently proposed technologies is presented for an islanded ammonia energy system. This process design consists of wind turbines and solar panels for electricity generation a battery for short-term energy storage an electrolyzer for hydrogen production a pressure swing adsorption unit for nitrogen production a novel ruthenium-based catalyst for ammonia synthesis a supported metal halide for ammonia separation and storage and an ammonia fueled proton-conducting solid oxide fuel cell for electricity generation. In a generic location in northern Europe it is possible to operate the islanded energy system at a round-trip efficiency of 61% and at a cost of about 0.30–0.35 € kWh−1 .

Nowadays the traditional energy sources used for greenhouse heating are fossil fuels such as LPG diesel and natural gas. The global energy demand will continue to grow and alternative technologies need to be developed in order to improve the sustainability of crop production in protected environments. Innovative solutions are represented by renewable energy plants such as photovoltaic wind and geothermal integrated systems however these technologies need to be connected to the power grid in order to store the energy produced. On agricultural land power grids are not widespread and stand-alone renewable energy systems should be investigated especially for greenhouse applications. The aim of this research is to analyze by means of a mathematical model the energy efficiency of a photovoltaic (8.2 kW) hydrogen (2.5 kW) and ground source gas heat pump (2.2 kW) integrated in a stand-alone system used for heating an experimental greenhouse tunnel (48 m2 ) during the winter season. A yearlong energy performance analysis was conducted for three different types of greenhouse cover materials a single layer polyethylene film an air inflated-double layer polyethylene film and a double acrylic or polycarbonate. The results of one year showed that the integrated system had a total energy efficiency of 14.6%. Starting from the electric energy supplied by the photovoltaic array the total efficiency of the hydrogen and ground source gas heat pump system was 112% if the coefficient of the performance of the heat pump is equal to 5. The heating system increased the greenhouse air temperatures by 3–9 ◦C with respect to the external air temperatures depending on the greenhouse cover material used.

In the automotive sector the zero emissions area has been dominated by battery electric vehicles. However prospective users cite charging times large batteries and the deployment of charging stations as a counter-argument. Hydrogen will offer a solution to these areas in the future. This research focuses on the development of a prototype three-wheeled vehicle that is named Neumann H2. It integrates state-of-the-art energy storage systems demonstrating the benefits of solar- battery- and hydrogen-powered drives. Of crucial importance for the R&D platform is the system’s ability to record its internal states in a time-synchronous format providing valuable data for researchers and developers. Given that the platform is equipped with the ROS2 Open-Source interface the data are recorded in a standardized format. Energy management is supported by artificial intelligence of the “Reinforcement Learning” type which selects the optimal energy source for operation based on different layers of high-fidelity maps. In addition to powertrain control the vehicle also uses artificial intelligence to detect the environment. The vehicle’s environment-sensing system is essentially designed to detect distinguish and select environmental elements through image segmentation using camera images and then to provide feedback to the user via displays.

The hydrogen storage pressure in fuel cell vehicles has been increased from 35 MPa to 70 MPa in order to accommodate longer driving range. On the downside such pressure increase results in significant temperature rise inside the hydrogen tank during fast filling at a fueling station which may pose safety issues. Installation of a chiller often mitigates this concern because it cools the hydrogen gas before its deposition into the tank. To address both the energy efficiency improvement and safety concerns this paper proposed an on-board cold thermal energy storage (CTES) system cooled by expanded hydrogen. During the driving cycle the proposed system uses an expander instead of a pressure regulator to generate additional power and cold hydrogen gas. Moreover CTES is equipped with phase change materials (PCM) to recover the cold energy of the expanded hydrogen gas which is later used in the next filling to cool the high-pressure hydrogen gas from the fueling station.

The decreasing abundance of conventional energy resources of nature such as crude oil natural gas and coal is putting forward the issues of energy shortcoming for the future. With a sentiment of this most researchers are now directing either on non-conventional resources that already prevail or invent it. The most promising non-conventional energy resource is the hydrogen energy which can be used in fuel cell to get electricity. Therefore a number of researchers are putting a light on developing the most efficient and affordable fuel cell. This review is mainly focused on the developments of proton exchange membranes (PEMs) in two parts as low and high temperature PEMs for proton exchange membrane fuel cell (PEMFC) and based on that some outperformed PEMs are mentioned in the respective tables. Most of the energy and automobile industries are concentrating to apply PEMFCs for power generation and to apply in vehicles. The cost of PEMFCs is higher due to the manufacturing cost of PEM. Therefore research works in PEMs are now in trend to reduce the cost to improve efficiency and to withstand particular operating conditions. In this review article recent developments in PEM by number of researchers and the importance of it in near future have been elicited.

Interest in reducing the greenhouse gas emissions from conventional power generation has increased the focus on the potential use of hydrogen to produce electricity. Numerous life-cycle assessment (LCA) studies of hydrogen-based power generation have been published. This study reviews the technological and methodological choices made in hydrogen-based power generation LCAs. A systematic review was chosen as the research method to achieve a comprehensive and minimally biased overview of hydrogen-based power generation LCAs. Relevant articles published between 2004 and 2021 were identified by searching the Scopus and Web of Science databases. Electrolysis from renewable energy resources was the most widely considered type of hydrogen production in the LCAs analyzed. Fuel cell technology was the most common conversion equipment used in hydrogen-based electricity LCAs. A significant number of scenarios examine the use of hydrogen for energy storage and co-generation purposes. Based on qualitative analysis the methodological choices of LCAs vary between studies in terms of the functional units allocations system boundaries and life-cycle impact assessment methods chosen. These discrepancies were likely to influence the value of the environmental impact results. The findings of the reviewed LCAs could provide an environmental profile of hydrogen-based electricity systems identify hotspots drive future research define performance goals and establish a baseline for their large-scale deployment.

Steel production is a carbon and energy intensive activity releasing 1.9 tons of CO2 and requiring 5.17 MWh of primary energy per ton produced on average globally resulting in 9% of all anthropogenic CO2 emissions. To achieve the goals of the Paris Agreement of limiting global temperature increase to below 1.5 °C compared to pre-industrial levels the structure of the global steel production must change fundamentally. There are several technological paths towards a lower carbon intensity for steelmaking which bring with them a paradigm shift decoupling CO2 emissions from crude steel production by transitioning from traditional methods of steel production using fossil coal and fossil methane to those based on low-cost renewable electricity and green hydrogen. However the energy system consequences of fully defossilised steelmaking has not yet been examined in detail. This research examines the energy system requirements a global defossilised power-to-steel industry using a GDP-based demand model for global steel demands which projects a growth in steel demand from 1.6 Gt in 2020 to 2.4 Gt in 2100. Three scenarios are developed to investigate the emissions trajectory energy demands and economics of a high penetration of direct hydrogen reduction and electrowinning in global steel production. Results indicate that the global steel industry will see green hydrogen demands grow significantly ranging from 2809 to 4371 TWhH2 by 2050. Under the studied conditions global steel production is projected to see reductions in final thermal energy demand of between 38.3% and 57.7% and increases in total electricity demand by factors between 15.1 and 13.3 by 2050 depending on the scenario. Furthermore CO2 emissions from steelmaking can be reduced to zero.